512 EM 385-1-1 Chapters 16-22

Sections

16-3. Personnel Required Qualification/Training.

Lifting and Handling Equipment (LHE) Operator Requirements

Only trained, certified, and designated personnel may operate LHE, with the employer verifying their qualifications.
Trainees may operate under supervision, and maintenance personnel may operate for specific functions under strict conditions.

Lift Director Requirements

The Lift Director must be competent and qualified to handle lift operations and responsible for developing, reviewing, and approving lift plans.

Crane Operator Requirements

Operators must pass written and operational tests, with their qualifications verified by the employer including knowledge of safety requirements and operation manuals.
Operators need to demonstrate comprehension of language, arithmetic skills, and the ability to use load charts and follow procedures.

Class I Crane Operator Training

Initial training requires a minimum of 24 hours, with content based on equipment type and class logistics, focusing on ASME B30 requirements.
Refresher training is mandatory every five years, with a minimum duration of 8 hours.

Class II Crane Operator Training

Initial training requires a minimum of 2 hours, tailored to the equipment type and class logistics, concentrating on ASME B30 requirements.
Refresher training should be conducted every five years, lasting at least 1 hour.

Knowledge Check Choose the best answer for the question.

16-2. Initial Class I Crane Operator training requires a minimum of _____.

2 hours

12 hours

24 hours

40 hours

You forgot to answer the question!

EM 385-1-1 Paragraph 16-3 (a.–e.).

16-3. Personnel Required Qualification/Training. (a.–e.).

a.  Only properly trained, certified, and qualified personnel that are designated in writing by the employer may operate LHE.  Prior to designating any LHE operator, the employer must obtain the intended operational functions and proof of qualifications for the operator.  The employer may designate the following personnel to operate LHE under limited conditions:  (16-3.a)

(1)  Trainees under the direct supervision of the designated operator of the LHE.

(2)  LHE maintenance, inspection, and repair personnel are permitted to operate the equipment only where all of the following requirements are met:

(a)  The operation is limited to those functions necessary for maintenance, equipment inspection or performance verification.

(b)  No lifting of loads.  They may only operate the equipment under the direct supervision of a qualified operator or they must read and review the specific LHE operations manual so that they are familiar with the operations, limitations, characteristics, and associated hazards.

b.  Lift Director Requirements.  Must be competent and qualified on lift operations and have the ability to develop, review and approve lift plans.  (16-3.b )

c.  Crane Operator Requirements.  (16-3.c )

(1)  Crane operators must successfully complete written and operational testing to become certified.

(2)  Qualification of all crane/hoist operators must be made by the employer after a review of the certification documents.  Qualification includes completed certification documents. Qualifications also include employer verification that the operator is familiar with the equipment and has adequate knowledge of USACE and OSHA crane safety requirements and the procedures and recommendations in the specific crane’s
    operation manual.

(3)  Crane operators must demonstrate their ability to read, write, and comprehend the language of the crane manufacturer’s operation and maintenance instruction materials.  They must exhibit acceptable arithmetic skills, be able to use load charts,
    and follow written manufacturer’s procedures applicable to the type and configuration of the equipment.

(4)  Operators of A-frame non-slewing anchor handling barges or vessels must be trained in the anchor handling barge system operation.

d.  Class I Crane Operator Training.  (16-3.d)

(1)  Initial.  Training duration is a minimum of 24 total hours.  The trainer must determine the necessary duration based on the type of equipment, logistics (for example, classroom, outdoors), class size, and other factors.  The syllabus must address the applicable ASME B30 requirements for successful completion of written and practical/operational examinations.

(2)  Refresher. Conduct refresher training at least once every five years. Recertifications may require more frequent refresher training.  Training duration is a minimum of 8 hours total.  The trainer must determine the necessary duration based on the type of equipment, logistics (for example, classroom, outdoors), class size, and other factors. The syllabus must address the applicable ASME B30 requirements for successful completion of written and practical/operational examinations.

e.  Class II Crane Operator Training.  (16-3.e)

(1)  Initial.  Training duration is a minimum of 2 hours total.  The trainer must determine the necessary duration based on the type of equipment, logistics (for example, classroom, outdoors), class size, and other factors.  The syllabus must address the applicable ASME B30 requirements for successful completion of written and practical/operational examinations.

(2)  Refresher. Conduct refresher training at least once every five years. Recertifications may require more frequent refresher training.  Training duration is a minimum of 1 hour. The trainer must determine the necessary duration based on the type of equipment, logistics (for example, classroom, outdoors), class size, and other factors. The syllabus must address the applicable ASME B30 requirements for successful completion of written and practical/operational examinations.